2 Things That Are Bothering Me

Hey All,

First time post he

I'm using Photoshop CS6, trying to make a selection using a quick mask and a brush. Normally I would put the quick mask on, paint in my selection using a brush preset and then turn off the mask, invert the selection, and use refine selection to make it a new layer.

Now when I turn off the mask, I get the error "no pixels are more than 50% selected". I've seen on other forums that feathering can be a problem, but as far as I know the brush preset I'm using has no feathering. In fact, I just reset the tools and tried again and it still gives me that error. I've definitely selected the correct layer because there's only one to select.

Any advice?

Thanks! M

Whenever I use the Polygonal Lasso tool lately, and then modify the brightness of the item selected, it creates a "GLOW" around the *outside* of what I have selected. So when I deselect it, there is now this "aura" around the item.

I have gone into all the settings, messed with "Feather" and the 4 or 5 other options and I see no way to eliminate this. There should be no changes outside of the selected item. Yet it seems to be reaching past the selection line just a bit, all the way around.

Examples attached.

I've been told to use the direct selection tool in a lot of the tuts I do. When I try it, all I get is a rectangle marquee that disappears when I un click. It does nothing for me, no lines of any kind.
I'm thinking maybe I have to hold down another key to use this.

Can you tell me or direct me to a page with some instruction on using the direct selection tool? I use the regular pen tool pretty good, so it's not that.
Thanks.

I am sorry if I don't use the correct jargon throughout this post, I am a very occasional user of Photoshop!

I have Photoshop CS4 Extended.

I want to create an "inverse" layer.

Here's what I mean:

1) create a new canvas.

2) Choose a large, bold font and write on the canvas (E.g. "Hello World").

3) Select all the letters (using the magic wand tool, click on each letter while holding down the shift key)

4) Invert the selection.

5) Get stuck, no idea what to do next. Try various things and get nowhere!

I want to make a new layer that contains the inverted selection as a shape that I can do things to like any other shape (e.g. in the shape library).

So, for example, I could fill the surrounding area with red and the letters will be transparent.

I've tried converting the inverted selection to a clipping mask, but after that I get in a bugger's muddle.

Perhaps I am going about this in completely the wrong way? Perhaps there's a better way?

Once again, I apologise if I sound like a three-year-old trying to explain something to an adult, but that's the extent of my knowledge of Photoshop!!

i am sure this should be relatively easy , but just don't know how ?? , i basically want to create something like this :



notice the "dots" are actually rectangular .

now this can be achieved with the pen tool and than using a brush and doing "stroke path" but there is a problems :

-- with the pen tool its difficult to get the circular shape .

is there a better way of doing this ? or does it just require better precision with the pen tool ??

i wanted to create such lines and use it like in a picture like this :



if somebody can give me a really vague idea , as to how i could , it will be great .

Thanks .

Gautam.

Hey Guys,

Is there a way to get photoshop to frame its view upon whatever is selected. ie. If a make a small selection within a canvas, which is off set because I'm working in another area, I'd like to be able to press something & have PS focus/centre its view upon that selection. I'm a 3d Artist & 3ds Max has a feature like this which is activated by pressing the Z key. I appreciate its not as important as within a 3d environment but my hands are getting tired panning & zooming around constantly.

Cheers.
George

Im new to PS idk if this is the right place to post this question but here. I'm following a tuto from http://www.photoshopessentials.com/p...isplay-effect/ i get to step 5 and for some reason when i hold shift and click not all lines stay selected why is this? as you can see in the pic red circles are selected green not selected.

Hi,
1st post in here so here goes with my cherry ..... be kind

I've been using Gimp for a while so not totally green but certainly not strong in the "Editing Department" and have just switched to CS6

I always have a problem trying to replace skies where there's not a clear distinction between sky and ground and where there's a ground mist or sea mist but appreciate the software is also struggling as it's not that clear and wonder if anyone has any better / easier ways than I've tried so far.

Here is the one I've struggled with



I've tried using colour range as well as the quick selection tool and the magic wand tool and the magnetic lasso. the quick selection tool would be the easiest but as I drag from left ti right it starts off fine and then all of a sudden as the sky darkens it suddenly gobbles up the sea with it and goes straight to the land. The Magic Wand takes ages as I start with one tolerance and then change accordingly to reduce the tolerance going from left to right, The Magnetic lasso I had a reasonable amount of success dividing between the land and sea but when I then try to do the straight vertical lines either side and the horizontal along the top despite being outside of the frame it creates a jagged line that keeps dropping down into the sky in places.

Any help would be appreciated but please be aware my understanding of some "jargon" goes waaaaaayyyyyy over my head, I can copy how people are doing it in you tube vids parrot fashion but I often have absolutely no comprehension what it means nor how one interacts with the other.... ie layers, masks etc

Actually if anyone knows of good spoon fed tutorials for those would appreciate as I really am struggling to get my head round them.

Hello! Very much so a noob question . ive done my research and im just here for a very definite tutorial . im learning how to resize images from Big to small. Only problem is i cant seem to keep the high quality resolution . Ive included both images .. the "moonshine" collage is what id like to minimize. The "Whiskey" image is able to be downsized with no resolution loss when i downsize why? ID also like to keep them PNG or transparent in the background .

the moonshine collage image is one i made in photoshop cs6.

id like to make them W:280 pixels H:110 pixels/100 pixels



Theres a screen shot of the photo in place . The GREEN image is the image in low resolution , which i cannot figure why . the other RED image is how id like all my images to appear . There both pretty big original images as well ..

I am doing a tutorial that calls for dotted lines. I believe this tut is done with the newest version of Photoshop out there, so it has no problem making dotted lines. But I just cannot find a way to make them with my CS3. Dotted lines have always been easy in other graphics programs I've used.

I tried going to Style/ Dotted Strokes and I get a halfway decent result by using "no fill". But I can't get the lines in any color except white or black. It's not very editable, either.

Is there a way to get dotted lines or strokes with CS3?

Thanks,
pslane